Victron Energy
Victron MultiPlus-II 12/4k/160-50 120V Inverter/Charger — 3.4kW, 160A Charger (12V High-Output, UL 458)
Victron MultiPlus-II 12/4k/160-50 120V Inverter/Charger — 3.4kW, 160A Charger (12V High-Output, UL 458)
Couldn't load pickup availability
The Victron MultiPlus-II 12/4k/160-50 120V is the most powerful 12V MultiPlus-II. It delivers 3.4 kW continuous of pure sine wave power and 4.0 kW for an hour from a cold start, and its 160A battery charger is the largest in the 12V range. It's the step up from the 12/3000 for RVs, vans, boats and off-grid cabins that want to stay at 12V but run bigger loads like air conditioners, induction cooktops and microwaves, and recharge a large lithium bank quickly.
It combines an inverter, a multi-stage charger and a 50A automatic transfer switch in one unit. If shore or generator power drops, it takes over the load in under 20 milliseconds, so computers and electronics keep running without interruption.
Why choose the 12/4k
- 3.4 kW continuous at 25°C (3.1 kW at 40°C), 4.0 kW for 1 hour and 4.5 kW for 30 minutes from a cold start, with a 6 kW peak for 2 seconds for motor starts.
- 160A charger, 33% more than the 12/3000's 120A, with an adaptive multi-stage charge profile and battery temperature sensing.
- PowerControl and PowerAssist: set a shore or generator current limit and the MultiPlus-II tops up from the battery when demand exceeds it. A 30A RV pedestal or a small generator can then run loads it couldn't handle alone.
- Two AC outputs: a no-break main output, plus a 32A auxiliary output that's only live when AC input is present. Use it for a water heater or other loads that shouldn't drain the battery.
- Scales up: two units for a 120/240V split-phase output, up to 6 in parallel, or three-phase.
- ESS capable, and works with MPPT solar charge controllers and grid-tie inverters. An optional 100A external current sensor extends PowerControl and PowerAssist.
- Full system integration: connect a Cerbo GX or Ekrano GX for free remote monitoring and control on VRM. Lithium battery communication runs through the GX device.
Specifications
| Part number | PMP122405100 |
| Battery voltage | 12V (DC input range 9.5–17V) |
| Output | 120VAC ±2%, 60Hz ±0.1%, pure sine wave |
| Continuous power | 3.4 kW at 25°C / 3.1 kW at 40°C / 2.4 kW at 65°C |
| Time-limited power (cold start) | 4.0 kW for 1 h · 4.5 kW for 30 min |
| Peak power | 6 kW for 2 s |
| Maximum efficiency | 93% |
| Zero-load power | 18 W (11 W AES mode, 4 W search mode) |
| Charger | 160A max · absorption 14.4V · float 13.8V · storage 13.2V |
| AC input | 90–140VAC, 55–65Hz · 50A transfer switch · 50A max input |
| Auxiliary output | 32A |
| Programmable relay | Yes (alarm, DC undervoltage or genset start/stop) |
| Communication | VE.Bus, 2× general purpose ports, remote on/off |
| Battery connection | 2×2 M8 bolts |
| 120VAC connection | 13 mm² (6 AWG) |
| Operating temperature | -40 to +60°C (-40 to 140°F), fan assisted |
| Enclosure | Steel, blue RAL 5012 · IP22 |
| Dimensions (H × W × D) | 631 × 277 × 164 mm (24.8 × 10.9 × 6.5 in) |
| Weight | 22 kg (49 lb) |
| Listing | UL 458 |
| Safety | EN-IEC 60335-1, EN-IEC 60335-2-29, CSA 22.2 107.1-16 |
Installation note
At 4 kW on a 12V bank, DC current can exceed 350A. Use short, heavy battery cables, a correctly rated Class-T or MEGA/ANL fuse, and a battery bank able to deliver that current. Configuration uses VictronConnect with a VE.Bus Smart dongle, or VEConfigure with an MK3-USB interface.
Sold by Jonsson Tech, an authorized Victron Energy dealer and installer in Spring, Texas. This is a genuine Victron product with the full manufacturer warranty, and US-based technical support from people who install these systems. Need help sizing cables, fusing or a complete system? Just ask.
Share
